Skip to content
Cowboy's Air Conditioning & Heating (210) 495-7771
← All articles
Heating·5 min read·

Furnace Pilot Light Out? How to Relight It Safely

When the pilot light goes out, a gas furnace cannot light its burners, so the house stays cold. Often you can relight it yourself in a few minutes. Here is how to do it safely, how to tell if your furnace even has a pilot light, and what it means when the pilot will not stay lit.

Illustration: A gas furnace burner flame
Pilot light or igniter?

First: do you smell gas?

Before you touch the furnace, take a breath. Natural gas has an added smell, often described as rotten eggs. If you smell gas, do not try to relight anything.

  1. Leave the house and take everyone with you, pets too.
  2. Do not flip light switches, use the thermostat, light a match or start a car in the garage.
  3. Once you are outside, call 911 or your gas utility. In San Antonio that is usually CPS Energy.
  4. Do not go back in until they say it is safe.

If there is no gas smell, you can move on to the steps below.

Does your furnace even have a pilot light?

Many people go looking for a pilot light that is not there. Most newer gas furnaces do not have a flame that burns all the time. They light the burners with an electronic igniter instead, either a hot surface igniter that glows orange or a spark igniter.

  • Standing pilot: common on older furnaces. You will see a small blue flame through a little window or opening near the burners, and the gas valve has a knob marked OFF, PILOT and ON.
  • Electronic ignition: there is no flame until the thermostat calls for heat. The gas valve usually has a simple ON/OFF switch or knob, and there is nothing to light by hand.

The lighting instructions are printed on a label inside the furnace door or on the burner cover. That label tells you which type you have. If yours has electronic ignition, skip to no pilot light? Check these instead.

How to relight a furnace pilot light

Always follow the label on your furnace first, since the steps and wait times vary by brand. For most standing-pilot furnaces, the process looks like this:

  1. Turn the thermostat down or to OFF so the furnace is not calling for heat.
  2. Remove the front access panel and find the gas control valve and the pilot opening.
  3. Turn the gas knob to OFF and wait. The label will say how long, often around five minutes. This lets any gas that built up clear out. If you smell gas at this point, stop and leave the house.
  4. Turn the knob to PILOT.
  5. Press and hold the knob (or the separate reset button) to start gas flowing to the pilot. Then light it with the built-in igniter button or a long fireplace lighter held at the pilot opening.
  6. Keep holding the knob for the time the label says, often 30 to 60 seconds, after the pilot lights. This heats the safety sensor so it keeps the gas on.
  7. Let go slowly. The pilot should stay lit. If it goes out, wait and try again once or twice, then stop.
  8. Turn the knob to ON, put the access panel back, and set the thermostat to heat. The burners should light within a minute or two.

Keep your face and hands back from the opening, and never use a short match or lighter that puts your fingers near the burner area.

What a healthy pilot flame looks like

A good pilot flame is steady and mostly blue, and it wraps around the tip of the sensor next to it. Watch for:

  • A weak, small or flickering flame that barely touches the sensor. It may not keep the sensor hot enough, so the pilot goes out again.
  • A lazy yellow or orange flame, or soot around the pilot. That points to a dirty pilot or a burning problem that a technician should check.

Why does the pilot light keep going out?

One outage now and then can happen. A pilot that goes out again and again is telling you something.

1. A worn or dirty thermocouple. The thermocouple is a small metal rod that sits in the pilot flame. When it is hot, it tells the gas valve to stay open. When it wears out or gets dirty, the valve shuts the gas off even though the pilot was lit. This is one of the most common reasons a pilot will not stay lit.

2. A dirty pilot opening. Dust and soot can clog the tiny pilot opening, so the flame comes out weak and does not heat the thermocouple well.

3. Drafts. A strong draft near the furnace, like an open attic hatch or a missing panel, can blow out a small flame.

4. A gas supply problem. If other gas appliances are also acting up, the problem may be with the gas supply, not the furnace.

5. A safety control doing its job. Some furnaces have sensors that shut the gas off if the exhaust is not venting right or flames roll out of the burner area. If one of these trips, do not keep relighting. That is a job for a technician. See what to do if a CO detector goes off and the dangers of a bad furnace.

No pilot light? Check these instead

If your furnace uses electronic ignition and will not light, there is nothing to relight by hand. A few things are safe to check:

  • The thermostat is set to HEAT and a few degrees above room temperature, and its batteries are good.
  • The furnace power switch (it looks like a light switch on or near the furnace) is on, and the breaker has not tripped.
  • The furnace door is closed all the way. Many furnaces will not run with the door off.
  • The air filter is not clogged.
  • The gas valve on the pipe to the furnace is open (the handle runs in line with the pipe).

If those are fine, the cause is usually a part such as the igniter, the flame sensor or a safety switch. See heater not turning on, what a flame sensor does and furnace keeps shutting off.

When to stop and call a technician

  • You smell gas at any point.
  • The pilot will not light, or it goes out again after two or three tries.
  • The pilot stays lit but the burners will not come on.
  • The flame is yellow or sooty, or you see scorch marks around the burner area.
  • A carbon monoxide alarm has gone off.
  • You are not comfortable working near the gas valve. That is a good reason on its own.

A technician can clean or replace the thermocouple, clean the pilot, check the gas pressure and the venting, and make sure the safety controls work. A yearly tune-up before heating season catches most of these problems early. See our maintenance plan.

Cowboy's answers 24/7 with our own dispatch on Blanco Road. See furnace repair in San Antonio, heating repair, or call (210) 495-7771.

Frequently asked questions

How do I relight the pilot light on my furnace?

Turn the thermostat down, turn the gas knob to OFF and wait the time on the label, often about five minutes. Turn the knob to PILOT, press and hold it while you light the pilot, keep holding for the time the label says, then release and turn the knob to ON. Always follow the instructions printed on your furnace, and stop if you smell gas.

Why does my furnace pilot light keep going out?

The most common reason is a worn or dirty thermocouple, the small sensor that keeps the gas on while the pilot is lit. A dirty pilot opening, drafts, a gas supply problem or a tripped safety control can also cause it. If it goes out again after two or three tries, call a technician.

Do newer furnaces have a pilot light?

Most newer gas furnaces do not have a pilot flame that burns all the time. They use an electronic igniter that lights the burners only when the thermostat calls for heat. The label inside the furnace door shows which type you have.

Is it safe to relight a furnace pilot light myself?

It is usually safe if there is no gas smell and you follow the instructions on the furnace label. If you smell gas, leave the house and call 911 or your gas utility from outside. If you are not comfortable with it, have a technician do it.

What color should a furnace pilot light be?

A healthy pilot flame is steady and mostly blue, and it wraps around the tip of the sensor. A weak, yellow or sooty flame usually means the pilot needs cleaning or the furnace needs service.

Related service: furnace repair in San Antonio · heating repair · all heating and cooling services. Cowboy's AC answers 24/7 at (210) 495-7771.

Cowboy's Air Conditioning & Heating · 6510 Blanco RdSan Antonio, TX

Keep reading.

All articles →
Illustration: A repair, measured not guessed
Air Conditioning · 5 min

Heater Not Turning On? 9 Things to Check Before You Call

Illustration: A repair, measured not guessed
Air Conditioning · 5 min

Furnace Keeps Shutting Off? 7 Causes of Short Cycling and What to Do

Illustration: The seasonal checklist
Air Conditioning · 4 min

Carbon Monoxide Detector Going Off? What to Do Right Now

Call now Callback